Firebrick
Whitacre Greer is a leading manufacturer of firebrick for the steel industry and home fireplaces. As with the pavers, dry-pressing provides consistency and uniformity, resulting in accurate dimensions and a higher quality finished product. Dimensional stability also makes for faster and easier installation. Dry-pressed fireplace brick are available in various sizes.
- Available in 2 colors of brick, buff and red.
- ASTM C-1261 Compliant
- Accurate Dimensions
For more information please visit the Whitacre Greer website or call our office at 800-334-0541
| Order Code | Product Description | Packaged | Min Order |
| FB8 | Fire Brick 8-1/4″x 4″x 2-1/2″ | 567/skid | 1 skid |
| FB8S | Fire Brick SPLITS 8-1/4″x 4″x 1-1/4″ | 928/skid | 1 skid |
| FB9 | Fire Brick 9″x 4.5″x 1.25″ | 500/skid | 1 skid |
| FB8R | RED Fire Brick 8-1/4″x 4″x 2-1/2″ | 567/skid | 1 skid |
| FB8RS | RED Fire Brick SPLITS 8-1/4″x 4″x 1-1/4″ | 928/skid | 1 skid |
Heat Stop (Dry)
These dry-mix refractory mortars are made from high temperature cements and carefully selected aggregates that will not expand or tear the mortar apart when heated. Once dried, these products are non-water soluble and more acid resistant than any other type of product used in these applications.
PRODUCT DATA
Formulation is similar to each other and developed for installation of firebrick and clay flue lining in masonry fireplace and chimney installations. They are the product of choice for masonry bread ovens, fireplace and chimney installations (interior or exterior) or where moisture may be present in masonry chimney installation.
- HEAT STOP-II is provided in a 10 lb. pail only.
- HEAT STOP-50 is provided in a 50 lb. bag only.
- For estimating purposes approximately 50 lbs. will lay up 100 firebricks (2 ½ inch thick) if joint thickness is 1/16 to 1/8 inch as recommended.
- Joint thickness up to 1/2 inch is acceptable with this product and is quite common.
- Add clean water (approximately 3/4 to 1 quart) for each 10 lbs. and mix thoroughly. No other additives required.
- Cold water works best. Warm water quickens set time. Do not remix or retemper this product as you would with a regular mortar.
- HEAT STOP-50 (50 lb. bag) yields approximately 60 lbs. of refractory mortar. This is the most economical per pound.
- Meets and exceeds ASTM C-199, ASTM C-1283, ASTM E-136.
- Meets and exceeds all local and national building codes including NFPA-211 and International Residential Codes, (1RC) and International Building Code (1BC) and etc.
- Color with masonry mortar color if desired. Follow color manufacturer’s instructions as if using a regular masonry mortar.
- Good for applications well over 2,000°F.
| Order Code | Product Description | Packaged | Min Order |
| HEAT50D | Heat Stop 50 lb. bag (DRY) | per bag | 1 bag |
| HEATD | Heat Stop 10lb. can (DRY) | per can | 1 can |
Heat Stop (Wet)
This convenient pre-mixed, ready-to-use product is available in one-gallon or 50-lb. pails. This product works well in firebrick installations such as fireplaces, boilers, furnaces and kilns. Available in gray or beige color. Water soluble.
PRODUCT DATA
HEAT STOP is a premixed and ready to use refractory mortar. It was developed for installation of firebrick in masonry fireplace installations. It also has many other uses such as in chimneys, boilers, furnaces, kilns and etc.
- This refractory mortar is gray in color and is shipped in 15 lb. and 50 lb. plastic pails.
- For estimating purposes 50 lbs. will lay up approximately 100 firebricks (2 ½ inches thick) if joint thickness is 1/16 inch to 1/8 inch as recommended.
- Mix thoroughly. No other additives required.
- If frozen, unfreeze and mix thoroughly.
- Meets and exceeds ASTM C-199 medium duty.
- Meets all local and national building codes.
- Good for applications well over 2000 0F.
- HEAT STOP premixed is an air setting product, however may be water soluble in service. Do not use on exterior applications or where excessive moisture may be present. Use HEAT STOP II or HEAT STOP – 50 non-water soluble products for moisture present applications.
TIP when using Heat Stop Premixed. For best results:
- Mix all of the contents in the container thoroughly before using.
- If, after mixing, the product still appears dry, add a little clean water and remix it thoroughly.
- For firebrick installation, keep the joints 1/16″ to 1/8″ thick.
This product may take longer to dry if the joints are thicker than 1/8″, and/or if conditions are extremely humid (such as after a recent rain). To enhance the drying in such conditions, open the damper, place a fan in front of it, or use other means to get some air or heat passing by the installation.
| Order Code | Product Description | Packaged | Min Order |
| HEAT50 | Heat Stop 50lb.pail (WET) | per pail | 1 pail |
| HEATS | Heat Stop 15lb. can (WET) | per can | 1 can |